how to make methamphetamine:

diluted hci also called muriatic acid can be obtained from hardware stores, in the pool section Na OH also called iye ethyl ether Et-0-Et- can be obtained from engine starting fluid usually from a large supermarket look for one that says "high ethyl ether content" such as prestone

ephedrine the cottons in todays vicks nasie inhalers dont contain efed of pfed (ephedrin or psuedoephedrin) but there are still lots of easy ways to get to the good ephed or pfed. pure ephedrin can be extracted out out of its plant matter. from a plant that can be bought from most garden stores. or you can get pfed from decongestive pills like sudafed. most people prefer to work with pfed from pills rather than ephed from the plant. the important thing is that you must have pure plediephed as any contaminants will fuck up the molar ratio leaving you with over-reduced shit or under reduced shit. or contaminants will jell during baseifying and gak up your product which will then be very hard to clean. so you want to find a pill that is nearly pure pfed hci. or as close to pure as you can get also check the lable on your pills and see what inactive ingredients they contain. inactive ingerdients are things like binders and flavors these you dont want and will remove when cleaning your pills. but certain inactive ingredients are harder to remove than others. you dont want pills with alot of cellose in them and you dont want pills with much wax you also dont want pills that contain povidone as a rule if you have two that contain the same amount pf pfed hci then take a smaller sized pill because it obviously has less binders and inactive ingredients.time released pills are usually harder to work with because they have more binders and tend to gel up during the a/b stage. also only active ingredient you have to first make ephedrine (which is sometimes sold as meth by itself) if you are selling it. I  would just make it really cheap, so you have no reason to use the nasty stuff from the tap. do things right 

list of equipment: a glass eyedropper *three small glass bottles with lids (approx. 3 oz. but not important) one one should be marked at 1.5oz, use tape on the outside to mark it (you might want to label it as ether) One should be clear (and it cant be the marked one

A pyrex dish (the meatloaf one is suggested) 

A glass quart jar

sharp scissors

clean rubber gloves

coffee filters

a measuring cup

measuring spoons

ethyl ether WARNING ethyl ether is very flammable and is heavier than air. Do not use ethyl ether near flame or non-sparkless motors. it is also an anesthetic and can cause respiratory collapse if you inhale to much

take the unmarked small bottle and spray starter fluid in it until it looks half-full. then fill the rest of the way with water, cap the bottle and shake for 5 minutes. let it sit for a minute or two. and tap the side to try and separate the clear upper layer, then draw off the topp (ether) layer with the eyedropper and throw away the lower (water) and cloudy layer. place the ether in the marked container. repeat this until you have about 1.5 oz of ether. put the cap on it. and put it in the freezer if you can . rinse the other bottle and let it stand. 

ethyl ether is very pungent even a small evaporated amount is quite noticeable. 5. pour 1/8 teaspoon of the iye crystals into the bottle of ephedrine and agitate. do this carefully, as the mixture will become hot, and give off hydrogen gas and/or steam. H2 gas is explosive and lighter than air , avoid any flames as usual repeat this step until the mixture remains cloudy this step neutralizes the HCI in the salt. leaving the insoluble free base (I-desoxyephedrine) again. why do we do this? so that we can get rid of any water-soluble impunities. for 3. oz botles. this should take only 3 repetitions or so 6 . fill the bottle from step 5 up the rest of the way with ethyl ether. cap the bottle. and agitate for about 8 minutes. it is very important to expose every molecule of the free-base to the ether for as long as possible. this will cause the free base to dissolve into the ether (it is soluble in ether) 

let the mixture settle. there will be a middle layer that is very thick. tap the side of the bottle to get this thin layer as thin as possible. this is why the bottle should be clear. 

8. remove the top (ether) layer with the eyedropper, being careful not to get any of the middle layer in it. place the removed ether layer into a bottle.

add to the third bottle enough water to fill it half way and about 5 drops of munatic the bottle for 2 minutes when it settles, remove the top layer and throw it away. The free base has now been bonded to the HCI again, forming a water soluble salt. This time, we're getting rid of ether-soluble impunities. Make sure to get rid of all the ether before going to step 11.
If there is anything left from step 3 repeat the procedure with it.

Evaporate the solution in the pyrex dish on low heat. You can do this on the stove or nuke it in the microwave (be careful of splashing) but i have found that if you leave it on top of a hot-water heater (like the one that supplies hot water to your house) for about 2-3 days the remaining crystals will be ephedrine HCI if you microwave it, I suggest no more than 5-10 seconds at one time if it starts “popping” that means you have to little liquid left to microwave. You can put it under a bright (100W) lamp instead.
Microwaving can result in uneven heating anyway.